How to change a Flat Tire?

By

1. Find a safe location

As soon as you realise you have a flat tire, do not abruptly brake or turn.  Slowly reduce speed and scan your surroundings for a level, straight stretch of road with a wide shoulder. An empty parking lot would be an ideal place. Level ground is good because it will prevent your vehicle from rolling. Also, straight stretches of road are better than curves because oncoming traffic is more likely to see you.

Never attempt to change your tire on a narrow shoulder near oncoming traffic. Keep moving (slowly) until you find a safer spot. While driving on a flat risks ruining your rim, replacing a rim is better than being hit by an inattentive driver.

Make sure to consult your owner’s manual and review their specific steps on how to change a flat tire for your vehicle

2. Turn on Hazard lights

Your hazard lights or “flashers” will help other drivers see you on the side of the road. To avoid an accident, turn them on as soon as you realize you need to pull over.

3. Apply Parking brake

Once stopped, always use the parking brake when preparing to replace a flat tire. This will minimize the possibility of your vehicle rolling.

4. Apply wheel wedges or keep a stone 

Wheel wedges go in front of or behind the tires to further ensure the vehicle doesn’t roll while you fix the flat tire. If you’re changing a rear tire, place these in front of the front tires. If your flat tire is at the front, put the wheel wedges behind the rear tires.

Bricks or large stones will work just as well as “real” wheel wedges. Just be sure they’re large enough to stop the car from rolling.

5. Remove the wheel cap or cover

If your vehicle has a hubcap covering the lug nuts, it’s easier to remove the hubcap before lifting the vehicle with the jack. If your lug nuts are exposed, you can skip ahead to Step 6.

Use the flat end of your lug wrench to remove the hubcap. This will work for most vehicles, but some hubcaps need a different tool to come off. Consult your owner’s manual for proper hubcap or wheel cover removal procedures.

6. Loosen the Nuts

Using the lug wrench, turn the lug nuts counterclockwise until you break their resistance. You may have to use force, and that’s ok. Use your foot or all of your body weight if necessary.

Loosen the lug nuts about ¼ to ½ of a turn, but don’t remove them completely yet. Save that for when it’s time to remove your tire/wheel from the vehicle.

7. Place the jack under the vehicle

The right place for the jack is usually beneath the vehicle frame alongside the tire that’s flat. Many vehicle frames have molded plastic on the bottom with a cleared area of exposed metal specifically for the jack. To safely lift and avoid damage to the vehicle, follow the instructions for jack placement in your vehicle owner’s manual.

8. Raise the vehicle with Jack

To prevent the jack from settling under the weight of your vehicle and coming off balance, place a small cut of 2×6” wood beneath it before attempting to raise your vehicle. This tactic is especially helpful on asphalt.

With the jack properly positioned, raise the vehicle until the flat tire is about six inches above the ground.

Never put any part of your body under the vehicle during or after raising the vehicle with the jack.

9. Unscrew the Nuts

Now it’s time to remove the lug nuts all the way. Since you’ve already loosened them, you should be able to unscrew them mostly by hand.

10. Remove the Flat Tire

Gripping the tire by the treads, pull it gently toward you until it’s completely free from the hub behind it. Set it on its side so that it doesn’t roll away.

11. Mount the spare wheel on Bolts

Now place the spare on the hub by lining up the rim with the lug bolts. Push gently until the lug bolts show through the rim.

12. Tighten the Nuts by Hand

Put the lug nuts back on the lug bolts and tighten them all the way by hand. Once they are all on, check each one again, tightening as much as possible.  You will tighten them with the wrench after lowering the vehicle to the ground.

13. Lower the Vehicle and tighten the Nuts again

Use the jack to lower the vehicle so that the spare tire is resting on the ground but the full weight of the vehicle isn’t fully on the tire. At this point, you should tighten the lug nuts with the wrench, turning clockwise, as much as you can.  Push down on the lug wrench with the full weight of your body.

14. Lower the Vehicle completely

Bring the vehicle all the way to the ground and remove the jack. Give the lug nuts another pull with the wrench to ensure they’re as tight as possible.

15. Replace the Hub Cap

If the hubcap you took from the flat tire will fit your spare, put it in place the same way you removed it initially. If it doesn’t fit, stow it away with the tire when you stow your equipment.

16. Put the equipment back

You have before you a jack, a lug wrench, wheel wedges, your flat tire, and possibly a hubcap. Don’t forget to put all of them in your vehicle before driving away.

17. Check the pressure in spare tire

You should check the tire pressure of the spare tire to make sure that it is safe to drive on. “T-Type” temporary spares, also called “mini-spares,” require 60 psi (420 kPa).  If the tire needs pressure, drive (slowly) to a service station immediately.

18. Get the Flat tire repaired at the earliest

Temporary spare tires aren’t made to drive long distances or at high speeds, so drive cautiously until you’re able to visit a tire technician. A professional should be able to determine whether your tire needs a repair or if it’s time to replace it.

How long does it take? 

Aside from taking your tire to a professional, the above procedure shouldn’t take more than 15 to 30 minutes to change a tire. Just be sure you don’t leave out any steps.

It’s beneficial practice changing a tire in your garage or driveway to ensure you’re ready to handle this situation if it ever happens to you.

Few more Tips: 

Knowing how to fix a flat tire is great, but regular tire maintenance is even more important. In addition to reviewing this guide regularly, remember to do the following:

  • Keep your tires properly inflated
  • Rotate your tires according to the manufacturer’s guidelines
  • Monitor for tread wear

All of these precautions will extend the life of your tires and reduce the likelihood of a flat. While there’s no way to prevent flat tires completely, proper care can improve performance and ensure your tires last as long as possible.

107 thoughts on “How to change a Flat Tire?”

  25. RonaldLisee

    Everything information about medication. Some are medicines that help people when doctors prescribe.
    ivermectin brand
    Learn about the side effects, dosages, and interactions. п»їMedicament prescribing information.

  99. Morrisdiedo

    Everything what you want to know about pills. Everything about medicine.
    tadalafil
    Read information now. Learn about the side effects, dosages, and interactions.

  105. Michaelbob

    Medscape Drugs & Diseases. Definitive journal of drugs and therapeutics.

    https://clomidc.fun/ buy cheap clomid no prescription
    Drugs information sheet. Definitive journal of drugs and therapeutics.

  106. Noummully

    Last year I was very tired, cause my iron levels were low so my onc had me take four infusions of Benefir sp generic cialis from india Another promising strategy for brain drug delivery is based on the use of ultrasound combined with microbubbles for inducing the BBB opening to locally and transiently deliver drugs into the brain

  107. learn more

    Whats up! I simply wish to give an enormous thumbs up for the good info you’ve right here on this post. I might be coming back to your weblog for more soon.

Leave a Comment

Your email address will not be published.

Copyright © 2022 Shutterdrives Media Pvt Ltd. All Rights Reserved
Privacy Policy